Immutable Page History Attachments

Diff for "docviper"

Page name: Diff for "docviper"
Differences between revisions 4 and 7 (spanning 3 versions)
⇤ ← Revision 4 as of 2019-11-09 13:43:30 →
Size: 1211
Editor: docviper
Comment:
← Revision 7 as of 2020-05-01 22:16:47 → ⇥
Size: 1322
Editor: docviper
Comment:
Deletions are marked like this. Additions are marked like this.
Line 6: Line 6:
Email: <<MailTo(OE5JFE AT SPAMFREE oevsv DOT at)>>
Line 7: Line 8:
Email: <<MailTo(OE5JFE AT SPAMFREE oevsv DOT at)>>
Line 9: Line 9:
Line 14: Line 13:
Projekt Ideen:
J-Pole Antenne für 2m/70cm		 Projekt Ideen: J-Pole Antenne für 2m/70cm
Line 21: Line 20:
===== Mini-Howto: Prusa-Slicer 2.1 für Lubuntu vom Source bauen ===== Tucnak als Log Tool für 1. Mai AOEE
https://devlol.org/wiki/docviper/tucnakforaoee
Line 23: Line 23:

===== Mini-Howto: Prusa-Slicer 2.1 für Lubuntu vom Source bauen =====

{{{
Line 24: Line 28:
}}}
Line 25: Line 30:
===== .tar.gz entpacken =====  ===== .tar.gz entpacken =====
Line 27: Line 32:
===== Nötiges installieren =====
Line 29: Line 33:
===== Nötiges installieren =====
{{{
Line 32: Line 38:

===== build ===== 		 }}}
===== build =====
{{{
Line 42: Line 48:

===== deb bauen ===== 		 }}}
===== deb bauen =====
{{{
Line 46: Line 52:

===== starten ===== 
 
prusa-slicer 



 }}}
===== starten =====
{{{
prusa-slicer
}}}

docviper aka Joe

Email: <OE5JFE AT SPAMFREE oevsv DOT at>

Name: Joe

QRZ: https://www.qrz.com/db/OE5JFE

Projekt Ideen: J-Pole Antenne für 2m/70cm

  • 300 Ohm Leitung von DX-Wire
  • RG 58 mit BNC oder SMA
  • Litze
  • Schrumpfschlauch mit Schmelzkleber

Tucnak als Log Tool für 1. Mai AOEE https://devlol.org/wiki/docviper/tucnakforaoee

Mini-Howto: Prusa-Slicer 2.1 für Lubuntu vom Source bauen

wget https://github.com/prusa3d/PrusaSlicer/archive/version_2.1.0.tar.gz

.tar.gz entpacken

Nötiges installieren

sudo apt install cpanminus cmake libboost-all-dev libtbb2 libtbb-dev libcurl4 libmkl-tbb-thread libcereal-dev libeigen3-dev expat libgtest-dev libcurl4-openssl-dev wx-common libplplotwxwidgets1 libwxgtk3.0-dev

cd PrusaSlicer-version_2.1.0/

build

perl Build.PL

mkdir build

cd build/

cmake .. -DCMAKE_BUILD_TYPE=Release -DSLIC3R_WX_STABLE=1

deb bauen

sudo checkinstall

starten

prusa-slicer

CategoryMember

MoinMoin Powered  |  Python Powered  |  GPL licensed  |  Valid HTML 4.01last edited 2020-05-01 22:16:47 by docviper